Feb 8, 2017

E80CC SRPP Line preamplifier Part 2

SRPP calculation

The heart of the SRPP is the 3 resistors used in this circuit (the upper one is generally omitted but it is bad practice if you want a perfectly balanced push pull). Easy to calculate they just depend upon tube parameters and AC load.
With a fully decoupled cathode all have the same value which is :

                                               R = Rload + ρ / µ -1,5

Current through tubes can be determined by the following formula

                                          Io = 1/2 [ Vht / 2 ρ + R ( µ +1,5 ) ]             Ohm's law...

Gain calculation is way more complicated and is an extrapolation of the simple triode gain mathematical relation

                  G = µ Rload [ ρ + R ( µ +1 ) ] / ( ρ + R )2 + Rload [ 2 ρ + R ( µ +1 ) ]

An Excel file makes a very handy tool to calculate all these parameters. Just has to be filled with tubes characteristics and AC load.



I also use it to determine the DC load RaV1. Drawing this load line on tube curves helps a lot to check linearity and allows to precisely set the working point (NB: This load to not take in consideration voltage drop in the 2 upper resistors, it is necessary to add it to anode voltage found on curves to have the exact Vak value).
This load is Io formula's denominator

                                                 RaV1 = 2 ρ + R ( µ +1,5 )



It is almost like a 47K loaded single tube and data sheet shows that we can expect very low distortion. In the case of a classic anode follower we have 4.1% mainly second order at 50Vrms!. In this preamp we deal with smaller voltages and the even harmonics will be greatly canceled by the SRPP configuration. Furthermore the 1.3K value has been selected using a HP 3561A dynamic analyzer to get the best distortion figure.
The SRPP operation will be very close to the Philips values, with a 57K load we have a 3.07 mA current for a 4V cathode voltage and a calculated gain of 18,11.



Line preamp schematic



Nothing special except an unusual input voltage divider. Gives some headroom on high level sources. Three positions, 0 -3 -6 dB permit a very fine gain control in association with the T pad. I used the excellent GRAYHILL 44 series rotary switches for both input/output selector and input attenuator. The quality is outstanding.
Like in the 6J5 line preamplifier just a few parts. Resistors are Holco H2, Philips (not Vishay) MRS25 and coupling capacitors ITT PMT/2R.

These are to my humble opinion (and to my friends ears...) some of the best caps for the price along with AEROVOX V161 and ERO MKC 1860 / KP1832. They give a very neutral and accurate restitution without spending hundreds on exotic parts for a somewhat slight improvement. I made tests with well-known pure copper or silver film and foil ones. There was an improvement in transparency or finesse on certain parts of the musical message but each time to the detriment of the overall tonal balance .....went back to the ITT's.

Looking inside...

Can't be a more compact wiring







Next step: power supply, fully assembled unit and tests

9 comments:

  1. Bonjour Fred,
    très beau projet, qui doit bien sonner. Je viens d'essayer les ITT PMT/2R sur mon préamp ligne 26, très bonnes capas en effet, son très liquide sans côté électronique, aigu très fin (juste neuves, pas rôdées...). Merci pour ce blog !

    Salutations.
    B r u n o

    ReplyDelete
    Replies
    1. Bonjour Bruno, content que les condensateurs ITT aient apporté une amélioration dans ton préampli.
      Fred

      Delete
  2. Hello! I'm at work surfing around yyour blog from my new iphone!

    Just wanted to say I love reading your blog annd look forward too all yiur posts!

    Keep up the outstanding work!

    ReplyDelete
  3. Hi are using Wordpress for your blog platform? I'm new to
    the blog world but I'm trying to get started and create my
    own. Do you require any coding knowledge to make your own blog?
    Any help would be really appreciated!

    ReplyDelete
    Replies
    1. Hi, I started with Blogger which is quite simple and intuitive.
      Just need the HTML basics for a faster and easier layout.
      Hope this helps.
      Fred

      Delete
  4. It's perfect time tto make some plans for the long run aand
    it is time to be happy. I have read this publish and if I
    may I want to recommend you few fascinating issues or
    suggestions. Perhaps you can write next articles referring to this article.
    I wish to learn more things about it!

    ReplyDelete
  5. No matter if some one searches ffor his vital thing, therefore he/she
    needs to be available that in detail, therefore that thing is maintained over here.

    ReplyDelete
  6. Your method of explaining the whole thing
    in this post iss really nice, all be apable of without difficulty be ware of it, Thanks a lot.

    ReplyDelete
  7. If you are going for best contents like myself, simply go to see this web site daily for the reason that it provides quality
    contents, thanks

    ReplyDelete