Jan 26, 2017

E80CC SRPP Line preamplifier Part 1

This project was initiated by a request of a line preamp with selectable input sensitivity to match sources with different voltage outputs. This preamp should also have a low output impedance to drive long connecting cables without any loss.
With such goals in mind it became evident that a simple 6J5 preamp would not fit these requirements.

1- The use of two gain control stacked together would greatly impact music transcription.
2- The gain of this preamp would have been too low to accommodate an input voltage divider up to -6dB.

A high gain stage with a voltage divider at input and a volume attenuator at output (which is the best way to control the gain from my humble opinion) was the way to go.

For that purpose there are a lot of good circuits with good linearity and gain, cascode, µ follower, totem pole, push pull. Push pull circuit, seldom used in preamplifier, is very interesting because it cancels all even harmonics. With such a circuit you can expect very low distortion using triodes but a phase splitter (transformer or tube) add complexity to the circuit, increases final cost and is hard to implement in a standard chassis.

One circuit shares this low distortion, high gain capability without the necessity of a splitter stage, the SRPP.

I have been working with for a long time and I know how it works (well), its limitations and drawbacks (very few when correctly understood and used).
Some would argue that it have a special sonic signature, especially on voices, with a kind of emphasis that could be appealing but do not reflects reality.
Believe me, when correctly used and adjusted (a FFT analyzer is of great help) it can be very neutral without being clinical or cold with huge dynamic and stunning resolution and accuracy on complex music.

SRPP (very) short history and use

Originally intended for video (1943) it was widely used to drive low impedance capacitive loads with high gain and wide bandwidth.

SRPP as it should be set up.



As indicated by its name, the SRPP is a push pull even if not evident at first glance.
I won't bother you with any mathematical demonstration because it is not the main topic and there are very good publications that help to understand this circuit, Audio Xpress The Optimized SRPP and Tube Cad SRPP deconstructed.
Never forget it works like a push pull only when loaded and gain, distortion, bandwidth greatly depend upon this load. Moreover its linearity is a direct relation with the flowing current which itself depends upon load.
The good thing is if you have a well defined load that won't vary with the amplifier connected behind, you can fine tune the circuit to get the lowest distortion playing with only 3 resistors. Reason why I choose to load my SRPP with transformer.

Finding a good one was easy because I had some Tamura on hand.
The TKS20 used in this preamp is a 600/10K line input transformer but can be reversed used as there is no current flowing through primary.
Tamura are among the best transformers I had to work with. Unfortunately most are discontinued and prices skyrocket on the second hand market.



Previously I said that the best way to control gain was the use of an attenuator behind the transformer. I was lucky enough to have some Daven 600 ohm dual T pad, perfect for the purpose.
These pieces of engineering are unbelievably well made with plain silver contacts and sorted resistors for perfect tracking. They were built to last a lifetime. The only disadvantage is a 6dB insertion loss that have to be taken in account when calculating overall gain.
These attenuators are very hard to find today, especially NOS, and it is interesting to build its own T or bridged T attenuator. See Pots & Attenuators tutorial.


Tube choice

To reach my goals I needed a tube that gives a minimum overall gain of 4 (attenuator will divide it by 2). This means a SRPP gain of 16,30 (transformer voltage ratio seen by tubes is 4,08) and a tube with a µ of 20/30, a ρ of 7/12 K to correctly match the 10K dynamic (AC) load.
Double triodes like 12BH7A,13D3,E80CC would be good candidates. In this study it is stated that V1 tubes are identicals.
I finally used the E80CC because I had excellent results in the E140 amplifier and it is easy to source compared to the British 13D3. I made some simulations with the 12BH7A but gain was too low.



More to come...







5 comments:

  1. Frédéric,
    Vite la suite afin ........ que je puisse réaliser le mien.
    Je suis un grand amateur du SRPP & de la E80CC.
    Pour le moment j'essaye de construire l'atténuateur a impédance constante.
    Ce n'est pas gagné.
    Philippe

    ReplyDelete
  2. Hello there, just became aware of your blog through Google, and found
    that it is truly informative. I'm gonna watch out for brussels.

    I will appreciate if you continue this in future. Many people will be benefited from your
    writing. Cheers!

    ReplyDelete
    Replies
    1. Hi and thanks for your comment.
      I will continue publishing schematics and studies.
      It just take quite a long time from the basic idea to the finished work as I do not want to come with design that would not be completely satisfying in terms of security, stability and of course music enjoyment.
      And to be truly honest I also need to have the necessary funds.
      Fred

      Delete
  3. Because the admin of this site is working, no doubt very rapidly it will be well-known, due to its
    quality contents.

    ReplyDelete
    Replies
    1. Thanks for your comment and glad to have readers, even a few, that are patient enough to stay interested by my work.
      Fred

      Delete